Vintageview MAG1 - 9 Magnum Bottle Rack User Manual download pdf

MAG1 or MAG2 contains:

MAG1 and MAG2 Wall Mount

Wine Rack Instructions

Wine Master Cellars •10645 E 47th Ave, Denver, CO 80239 • phone: 866.650.1500 • fax: 866.650.1501

Please feel free to contact us regarding the assembly of this product.

Tools Needed:

Before starting, open all Packaging for the MAG1 or MAG2 and take inventory to make sure you have everything.

• 1 Neck Strip

• 2 Plastic Couplers

• 1 Spirit Level

• 1 Marking Pen or Pencil

• 1 Tape Measure

• 1 Screwdriver

• Drill and Drill Bits (Necessary in Some Cases)

There are three pre-drilled mounting holes in each strip, six total per rack. Appropriate fasteners must be utilized in every

mounting hole for proper installation. Fasteners are not included with your MAG1 or MAG2. However, we recommend the

following fasteners for these surfaces:

Fasteners:

• Wood Surface: #8 x 1-1/4” wood screw

• Drywall/Wallboard Surface: #8 x 1-1/4” screw with spiral inserts for the bottom two holes in each strip (4 total) and

an expanding hollow wall anchor such as a toggle bolt for the top hole in each strip (2 total)

• Concrete, Brick or Stucco: 3/16” x 1 ¾” masonry screw or #8 x 1 ¼” screw with appropriate size expanding anchor

NOTE: If you are attaching the MAG1 or MAG2 to a VintageView® Floor to Ceiling Frame (FCF) you will attach the

units to the FCF using the self-drilling screws included in the FCF packaging.

MAG1 and MAG2 Installation Instructions

1 - Determine which direction the bottle necks

should point.

• 1 Base Strip

• 6 Rubber Mounting Hole Caps

1.1. If the bottle necks are to point to the right, the base

strip must be installed to the left of the neck strip.

1.2. If the bottle necks are to point to the left, the base

strip must be installed to the right of the neck strip.

2.1. The centerline of the rst strip (either base or neck

depending on bottle neck direction) should be at least 3-1/4”

from adjacent walls or obstructions. This allows for the bottle

to overhang the rack.

2.2. From centerline of the rst strip, measure 8-1/2” to the

centerline of the next strip.

Note: This dimension may be altered for specic bottle sizes.

If using the MAG1 or MAG2 racks for sparkling wines/Cham

pagne, we recommend using 7-1/2” as a centerline-to-cen-

terline measurement between the neck and the base strips.

2.3. (For multiple columns) locate the centerline of the next

strip 6” away from the prior strip.

2.4. (For multiple columns) continue marking the centerlines,

alternating between 8-1/2” (or 7-1/2” for sparkling wines/

Champagne) and 6-1/2” increments.

2 - Lay out the wall. (Fig. 1)

3 1/4"

Fig. 1

1 2

Summary of Contents

Page 1 - Wine Rack Instructions

MAG1 or MAG2 contains:MAG1 and MAG2 Wall Mount Wine Rack InstructionsWine Master Cellars •10645 E 47th Ave, Denver, CO 80239 • phone: 866.650.1500 •

Page 2 - Warranty

3.1. Reference the Fasteners section for recom-mended fastener types.3.2. Using a level, ensure that each strip is plumb prior to securing it to the w

Comments to this Manuals

No comments

Vintageview MAG1 - 9 Magnum Bottle Rack User Manual

Browse online or download User Manual for Equipment Vintageview MAG1 - 9 Magnum Bottle Rack. VintageView MAG1 - 9 Magnum Bottle Rack User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Equipment Vintageview MAG1 - 9 Magnum Bottle Rack