Each WS-PR kit contains:
Wall Strip Presentation Rack
(WS-PR) Installation Instructions
Wine Master Cellars • 10645 E 47th Ave, Denver, CO 80239 • phone: 866.650.1500 • fax: 866.650.1501
Please feel free to contact us regarding the assembly of this product.
Tools Needed:
Before starting, open all Packaging for the WS-PR and take inventory to make sure you have everything.
• 1 Wall Strip Presentation Rack (WS-PR)
• 8 Plastic Mounting Hole Caps (Bagged)
• 5 Plastic Couplers (Bagged)
• 6 Plastic End Caps (Installed)
• Level
• Marking Pen or Pencil (Necessary in Some Cases)
• Tape Measure (Necessary in Some Cases)
• Phillips Head Power Screwdriver
• The appropriate FASTENERS for the wall surface you are attaching the WS-PR to.
There are eight pre-drilled Mounting Holes for fasteners on each WS-PR Series Rack. It is strongly recommended that
appropriate fasteners be used in every Mounting Hole. We do not include fasteners with your WS-PR. However, we
recommend the following fasteners for these surfaces:
Fasteners:
• Wood Surface: #8 x 1-1/4” wood screw
• Drywall/Wallboard Surface: #8 x 1-1/4” screw with spiral inserts and/or
expanding hollow wall anchors such as toggle bolts
• Concrete, Brick or Stucco: 3/16” x 1 ¾” masonry screw or expanding anchor
NOTE: If you are attaching the WS-PR to a VintageView® Floor to Ceiling Frame (FCF) you will attach the WS-PR to
the FCF using the self-drilling screws included in the FCF packaging.
1.1 Remove the Black Plastic End Cap that is inserted into the
bottom of each of the four Mounting Braces on the WS-PR.
NOTE: If you will be installing the WS-PR next to other WS-
PRs also remove the Black Plastic End Caps on both sides of
the WS-PR and insert a Black Plastic Coupler to one side of
the WS-PR.
1.2 Remove the Black Plastic End Caps from the top of the
WS Series Racks that correspond to the Mounting Braces on
the WS-PR.
1.3 Insert the Black Plastic Couplers into the top of the WS
Series Strips.
1.4 Align the WS-PR Mounting Braces directly over the WS Wall
Strips and attach to the Wall Strips by sliding the WS-PR onto
the Couplers xed into the WS Series Strips.
Installation to a Wall
NOTE: If you are installing the WS-PR to a wall or FCF above or below a WS-3 or WS-4 Series Rack System:
Install the WS Series Racks before installing the WS-PR.
WS-PR Installation Instructions
1 - Installation to a Wall above WS Series Racks
1.5 Using the Appropriate Fasteners; mount the WS-PR to the wall
through the hole in each of the 4 WS-PR Mounting Braces, and the
hole above each Mounting Brace.
1.6 Attach the Black Plastic Mounting Hole Caps over the fasteners in
the 8 Mounting Hole
2 – Installation to a Wall below WS Series Racks
NOTE: If you will be installing the WS-PR next to other WS-PRs
remove the Black Plastic End Caps on both sides of the WS-PR and
insert a Black Plastic Coupler into one side of the WS-PR.
(Continued on back of sheet).
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals